Slips, Trips and Falls Prevention

Ensure your facility has the right practices, training and response plans in place.

How Do Slips, Trips and Falls Occur?

Slips, trips, and falls occur when there is too little friction or traction on a walking surface, when a foot or lower leg hits an object while the rest of the body continues to move, or when the center of balance is lost resulting in a descent to the floor, against an object or to a surface at a lower level than the original surface.1 These incidents are often caused by slippery, irregular or uneven surfaces, obstacles on the floor or uncovered/unidentified hazard areas.

Hazards relating to slips, trips and falls are frequently top offenders on OSHA's top 10 violation lists. In 2015 alone, slips, trips, and falls were tied to three of the top ten violations, and two of the top three. These violations included hazards relating to fall protection (#1), scaffolding (#3), and ladders (#7).2

Slips, Trips and Falls Guide

This free guide provides tools and resources that will help you learn about slips, trips and falls prevention in your workplace. Get it today!

Take a look at some visual workplace examples in this FREE guide:

Contact Us
Slips, Trips and Falls Guidebook

OSHA Standards that Help Prevent Slips, Trips and Falls

OSHA 29 CFR 1910.36 & 37
Means of Egress

This standard supports the safety of exit routes. Some of the key elements that apply to slips, trips and fall in this standard include:

  • The outdoor exit route must have guardrails to protect unenclosed sides if a fall hazard exists
  • The outdoor exit route must be reasonably straight and have smooth, solid, substantially level walkways
  • The outdoor exit route must be covered if snow or ice is likely to accumulate along the route, unless the employer can demonstrate that any snow or ice accumulation will be removed before it presents a slipping hazard

OSHA 29 CFR 1910.22 and 1910 Subpart D
Walking-Working Surface

This standard supports worker safety by keeping workplaces clean and safe from hazards, including:

  • Keeping facilities clean, orderly and dry
  • Providing draining, platforms, mats or other dry standing places when wet processes are used
  • Keeping floors and workplaces free from protruding nails, splinters, holes and loose boards
  • Keeping aisles clear and in good repair
  • Permanently marking aisles and passageways
  • Using covers and guardrails to protect workers from open pits, tanks, vats, etc.
  • Marking loads with approved plates and maintaining safe load weights
  • Safety requirements for scaffolding and ladders construction and use

Slips, Trips and Falls Prevention

You wouldn't be here if you didn't think slips, trips, and falls prevention was important. You also should know by now the implications of not taking the right steps to complying with OSHA's Walking-Working Surfaces standard and the potential dangers associated to non-compliance. Now, let's outline each step that you can take to prevent slips, trips and falls hazards.

  1. Assess Your Workplace
  2. Mark Aisles and Passageways
  3. Provide Traction on Slippery Surfaces
  4. Improve Stair Safety
  5. Mark Emergency Evacuation Routes
  1. Post Safety Signs and Labels
  2. Warn of Temporary Hazards
  3. Inspect Scaffolds and Ladders
  4. Control and Clean Oil and Spills
  5. Train Employees
Fallen Man Stick Figure

Building A Response Plan

Despite our best efforts, accidents sometimes happen. In the event that a slip, trip or fall does occur at your workplace, you need a plan that allows everyone to act quickly and effectively. When you're creating a response plan here are a few guidelines to keep in mind:

1. Provide assistance

This may sound like a given, but many times in the heat of the moment, those who immediately respond to an emergency may not know what to do. Make sure there is a clear and easy way to provide first aid or call for emergency medical assistance.

2. Report the incident


The appropriate personnel within your work place need to have a system in place to record slips, trips, and fall incidents. Furthermore, these incident reports should be kept to review common incident areas and provided to your insurance company.


3. Find ways to avoid the incident in the future

This is when you can identify area of training, different products or signage needs, and housekeeping practices that should be used to ensure employee safety and compliance to OSHA standards in the future.

Product Recommendations

Here are our top product recommendations to get you started.


Slips Trips Falls Guide

This free guide provides tools and resources that will help you learn about slips, trips and falls prevention in your workplace.

Download Now
Slips Trips Falls Prevention Checklist

Review your current safety program and ensure you have the right plans in place. This infographic offers some quick tips to get started.

Download Now
Slips Trips Falls Infographic

For information on how and where slips, trips and falls can occur in your workplace, check out this handy infographic.

Download Now